← Back to blog

Tri-Clamp Gasket Guide: Profile, Bore & Material

Silicone Clamp Gasket

Specify a replacement Tri-Clamp gasket by mating ferrule bore (A), gasket cross-section profile (plain, outer-lip flanged, or mesh screen), and both process media and CIP/SIP cleaning exposure—never order by flange OD (such as 50.5 mm) or generic elastomer charts alone.

1. Replace vs. re-tighten: stop criteria

Re-tightening a fatigued or heat-hardened seal risks extruding elastomer into the product stream without restoring sealing elasticity.

  • Compression set or flattening: the sealing bead no longer stands proud of the groove or feels stiff and brittle.
  • Surface nicks, radial cuts, or crazing: even minor knife/tool marks across the raised sealing bead create a capillary leak path.
  • Swelling, tackiness, or odor carry-over: check the actual process and cleaning exposure against the compound specification.
  • PTFE cold-flow / bore lip protrusion: solid PTFE creeps under repeated thermal cycles; replace once the inner bore lips inward or shows permanent step marks.
  • Screen gasket mesh distortion: replace any screen gasket showing torn wire, bent mesh, or trapped debris that resists validated cleaning.

2. Match bore (A) & profile (Plain / 13FG / Screen)

Catalog product specifications separate primary metric series ranges (DN20–DN100) from attached dimensional reference charts—always confirm mating ferrule bore A and groove profile.

Profile Type

Key Seating Feature

Documented Sizes

Buyer Verification

Plain annular (TC-GSK-*)

Seats inside groove; manual centering

DN20–DN100; chart 1/2"–8" (1.0" ID 22.7/OD 50.0; 1.5" ID 35.9/OD 50.0; unit unprinted)

Confirm 1" vs 1½" bore (50.5 mm) & 1/2" vs 3/4" (25.2 mm)

Outer-lip flanged (13FG)

Outer rim locates over ferrule OD

DN20–DN100; chart 1.0"–12" (1.0" ØA 22.8/ØB 52.7; 1.5" ØA 35.8/ØB 52.7; unit unprinted)

Check outer lip fits inside clamp pocket

Stainless mesh screen

Integral mesh captures particulates

DN20–DN100 (mesh rating not inferred from plain chart)

Specify micron/mesh requirement & flow side

Do not swap Tri-Clamp gaskets with BSM (AS 1528), RJT (BS 4825 Part 5), DIN 11851, SMS, or IDF union seals—their O-rings and flat seals fit threaded union grooves, not Tri-Clamp ferrule faces.

3. EPDM, Silicone, FKM & PTFE selection by duty

List production fluid, sanitizer, caustic/acid CIP strength, and steam/hot-water exposure separately when selecting spares:

  • Silicone (TC-GSK-SIL / TC-GSK-SIL-LIP): flexible, low-temperature seating on frequent-open hygienic joints; verify resistance against strong acids/alkalis, steam, and aggressive solvents.
  • EPDM (TC-GSK-EPDM): widely paired with water, aqueous solutions, and routine caustic/acid CIP cycles; verify exclusions around oils, fats, and hydrocarbons.
  • FKM / Viton (TC-GSK-FKM / TC-GSK-FKM-LIP): selected for oils, fuels, hydrocarbons, and specific chemical streams; dry-heat resistance does not establish steam suitability.
  • PTFE (TC-GSK-PTFE / TC-GSK-PTFE-SCREEN): broad chemical inertness across acids and solvents; less elastic than rubber, sensitive to cold flow/creep and seating load—verify ferrule face flatness.

Chelsey does not publish universal pressure or temperature limits for gaskets; compound suitability depends on the exact medium, concentration, and cycle confirmed per order.

4. Change-out alignment & 5-step assembly link

For the complete lockout, alignment, and model-specific tightening sequence, follow our Tri-Clamp Assembly & Leak Check Guide. During a gasket swap, focus on three additional checks: remove baked elastomer residue from the groove with a non-marring tool (never scratch the stainless sealing face), verify the new gasket bore sits flush with ferrule bore A (see Tri-Clamp Sizing Guide), and inspect cold after initial thermal cycling rather than tightening a hot joint.

5. Spare-parts BOM & catalog gasket SKUs

Include one line per bore size, profile, and compound when replenishing maintenance stock:

Silicone Tri-Clamp gasket (TC-GSK-SIL)plain annular seal, DN20–DN100View productEPDM Tri-Clamp gasket (TC-GSK-EPDM)plain annular seal, DN20–DN100View productPTFE Tri-Clamp gasket (TC-GSK-PTFE)plain chemical-resistant seal, DN20–DN100View productFKM (Viton) Tri-Clamp gasket (TC-GSK-FKM)plain annular seal, DN20–DN100View productOuter-lip flanged Silicone gasket (TC-GSK-SIL-LIP)self-centering 13FG profileView productPTFE stainless-mesh screen gasket (TC-GSK-PTFE-SCREEN)inline particle interceptionView product

Browse all Tri-Clamp Gaskets & Seals

  • Sample spares BOM line: Tri-Clamp gasket | 1½" OD-tube example (50.5 mm flange, bore A = 34.8 mm) | Plain EPDM | 50 pcs | Provide process fluid, cleaning concentration, temperature and contact time for compound verification.
  • Screen gasket BOM line: Tri-Clamp Screen Gasket | 2" OD-tube (Flange 64.0 mm, Bore A = 47.5 mm) | PTFE + SS Mesh (state target mesh size) | Process fluid + CIP cycle | 10 pcs.

Related posts

All resources
Tri-Clamp fittings range
Tri-Clamp · Oct 21, 2026

Tri-Clamp Assembly Guide: 5-Step Setup & Leak Checks

Follow a 5-step Tri-Clamp setup sequence—verify bores (especially 50.5 mm 1" vs 1½"), clean grooves, center the gasket, tighten by clamp/compound (never a single universal torque), and troubleshoot leaks after safe shutdown.

Read article
Complete Union Ferrule Set
Tri-Clamp · Oct 20, 2026

Tri-Clamp Size Guide: 1–4" OD Chart, 50.5 mm & Ferrules

Identify Tri-Clamp ferrule sizes using caliper dimensions A/B/C/D, separate 1" vs 1½" bores sharing the 50.5 mm flange, compare 14WMP/14MMP/14AMP/heavy-wall ferrules, and confirm DIN 32676 series boundaries.

Read article
Tri-Clamp Eccentric Reducer
Tri-Clamp · Nov 15, 2026

Tri-Clamp Reducers: Concentric vs. Eccentric & Sizes

Select Tri-Clamp reducers by both Large × Small ends, centerline geometry (concentric, eccentric, compact, end-cap, or bowl), horizontal flat-top/flat-bottom orientation, and verified SKU tables—never extrapolating unlisted pairs across series.

Read article
Chelsey stainless valve range
Sanitary valves · Oct 21, 2026

Sanitary Valves: Butterfly, Ball, Check & Diaphragm Selection

Compare valve flow paths, cleaning access and maintenance space. Two example duties show how water isolation and viscous-product service lead to different selections.

Read article

DIRECT FACTORY QUOTATION · WENZHOU

Quote a full BOM, stock order or unknown replacement part.

Send connection type, sizes, 304/316L grade, quantities and destination country—or share partial caliper measurements and unknown replacement items. After submitting, you receive an inquiry reference to reply by email with photos, PDF/STEP drawings or BOM spreadsheets.

Tell us what you need

Known part lists, partial caliper measurements or unknown replacement parts are all welcome.

Photos, drawings or BOM? Submit this form to get an inquiry number, then send files by email.

Cookie & privacy preferences

Choose which storage categories you allow. Privacy policy

NecessaryAlways enabled

Required to remember your privacy preference and active inquiry session.

Preference lifetime
180 days
Inquiry session
30 minutes
Analytics

Helps us understand catalog usage and improve technical pages.

Advertising measurement

Used only when ad campaign measurement is enabled.

About measurement

Analytics and advertising storage remain off until you grant consent.

You can revisit these preferences any time from the footer.