RJT, BSM and flat-faced CIP unions can be sold under similar names. Before ordering replacement nuts, liners or seals, identify the joint from the installed parts and the drawing for that model.
1. Why "BSM" and "RJT" spare parts do not always interchange
Nominal tube size is only one check. Compare dimensions taken at the same points on the mating threads, then verify the liner profile and the seal seat against the model drawing.
Series | Seal & Seat Geometry | Thread feature to verify | Primary Catalog Items |
|---|---|---|---|
RJT (BS 4825 Pt 5) | Conical liner nose + recessed O-ring / profiled groove | External thread OD and pitch on the male end. Check the mating nut against its paired drawing. | RJT-13H, RJT-14, RJT-15, RJT-SEAL-*, RJT-NUT-SLOT |
BSM (Stepped Liner) | Stepped retaining liner & bevel nose + O-ring/stepped seal | External thread OD and pitch on the BSM male end and the corresponding nut. | BSM-UNION-HEX, LINER-BSM, MALE-BSM, NUT-BSM-HEX, BSM-NUT-SLOT |
CIP Flat-Faced Union | CIP-14/CIP-15 flat sealing faces + raised-lip seal ring | External thread OD and pitch plus the documented flat-seat pairing. | CIP-UNION-FLAT-HEX, CIP-UNION-BLANK, SEAL-CIP-RAISED |
Measure the male thread OD and record the pitch. Photograph the mating liner and seal seat. Compare the measurements with the manufacturer drawing for both parts before ordering a loose nut or liner.
2. Identify all four union parts—and check grade availability per SKU
An assembled screwed union has four parts—union nut, weld liner, weld male part, and elastomeric seal. In Chelsey's documented catalog, wet-end weld liners, male ends, and complete hex assemblies offer AISI 304 and AISI 316L, whereas specialized C-spanner slotted nuts, chained blind nuts, and water-pusher blanks are listed in Grade 304:
- Hexagonal vs. slotted round nuts: Hex nuts tighten with standard flat wrenches (RJT-13H in 304/316L; NUT-BSM-HEX & NUT-CIP-HEX in 304/316L). Slotted round nuts (BSM-NUT-SLOT 1"–4" and RJT-NUT-SLOT 1"–6") use a C-spanner and are specified in Grade 304.
- Weld liner & male parts: Always pair RJT-14 + RJT-15 together, LINER-BSM + MALE-BSM together, or CIP-14 + CIP-15 together—confirming 1"–4" inch OD tube match and weld-end wall thickness.
- Material verification: Where brewery/CIP skids require 316L nuts alongside 316L liners, choose hex-nut SKUs with explicit 304/316L options rather than assuming slotted round nuts carry 316L variants.
3. Never guess union seals: O-ring vs. profiled vs. flat CIP
Elastomer seats are geometry-locked to the machined groove. RJT O-rings cannot sit cleanly in flat CIP faces, and flat-faced BSM EPDM gaskets follow different cross-sectional dimensions than RJT stepped seals:
- RJT-SEAL-O-EPDM (products:342) — Circular 6.6 mm cross-section EPDM O-rings for 1"–6" RJT recessed grooves.
- RJT-SEAL-PROFILED (products:597) — Stepped RJT seals in EPDM, FKM, PTFE, and NBR (with dedicated flat NBR profiles for ½" and ¾").
- BSM-SEAL-FLAT-EPDM (products:343) — Molded stepped flat-faced EPDM seal for 1"–4" flat BSM joints (alongside stepped SEAL-BSM-EPDM).
- SEAL-CIP-RAISED (products:330) — Raised-lip grooved seal ring in EPDM, Silicone, FKM, and NBR across 25–152 mm CIP unions.
4. Blanks, water pushers & RJT-to-BSP / Tri-Clamp transitions
Temporary tank isolation, hose changeovers, and CIP push-water injection rely on purpose-built closures and one-piece adapters rather than field welds:
- UNION-BLANK-DISC (products:331) — Solid BSM & RJT blank cap; select BSM or RJT profile first before confirming plate dimensions (1"–4" / ½"–6" tables differ).
- Chained RJT blind nuts (products:329 hex / 332 slotted) — Thread directly onto an open RJT male end in 304 SS without needing a loose disc or liner.
- RJT-BLANK-BSP-F Water Pusher (products:596) — 304 SS RJT blank pre-welded with a centered 15NB (½") or 20NB (¾") female BSP socket for purge/water hoses and gauges.
- Transitions (products:344, 333, 334, 335) — One-piece 316 SS RJT Male to Tri-Clamp (1"–4") plus RJT-to-BSPT/BSPP threaded adapters (½"–4").
5. Four-line ordering checklist & catalog links
Send these four details per line item so engineering confirms exact thread engagement and seal groove compatibility before quoting:
- Standard & seating profile: State RJT (BS 4825-5), stepped BSM, or flat-faced CIP—plus tube OD (1"–4") or caliper male thread OD.
- Component scope: Specify complete 4-part union assembly or individual nut (hex vs slotted), weld liner, male end, blank/blind nut, or water pusher BSP size.
- Alloy & seal compound: Confirm SS304 vs SS316L (noting 304-only items like slotted/blind nuts) and EPDM, FKM, Silicone, PTFE, or NBR seal.
- Mating conversions: For skid tie-ins or pump manifolds, link our RJT-to-Tri-Clamp or RJT-to-BSPP/BSPT adapters on the same BOM.
Sanitary Pipe UnionsView range
BSM-UNION-HEXStepped-Liner Hex Union Assembly (1"–4", 304/316L)View product
RJT-13H / RJT-14 / RJT-15Core RJT Union Components (304/316L)View product
BSM-NUT-SLOTSlotted C-Spanner Union Nut (1"–4", Grade 304)View product
















































